gp2a200lcs0f series 1 sheet no.: d3-a05101en date jun. 30. 2005 ? sharp corporation notice the content of data sheet is subject to change without prior notice. in the absence of con rmation by device speci cation sheets, sharp takes no responsibility for any defects that may occur in equipment using any sharp devices shown in catalogs, data books, etc. contact sharp in order to obtain the latest device speci cation sheets before using any sharp device. gp2a200lcs0f series detecting distance : 2 to 22mm * opic output, re ective photointerrupter with connector description gp2a200lcs0f series are opic output, reflective photointerrupters with emitter and detector facing the same direction in a molding that provides non-contact sensing. this family of devices uses light modulation to reduce the affects of disturbing light, and the sensor is optimized to work in the selected focal distance. a 3-pin connector is included to allow remote-mount or off-board designs. features 1. re ective with opic light modulated output 2. highlights : ? includes additional screw xing holes ? position pin to prevent mis-alignment ? long focal distance 3. key parameters : ? detecting distance : 2 to 22mm (white paper) 5 to 15mm (black paper) ? undetecting distance : over 90mm (white paper) ? connector : gp2a200lcs0f ; tyco electronics amp k.k. (pn : 292133-3) GP2A200LCSCF ; tyco electronics amp k.k. (pn : 292133-3) gp2a240lcs0f ; tyco electronics amp k.k. (pn : 292133-3) gp2a210lcsjf ; tyco electronics amp k.k . (pn : 4-292133-3) 4. lead free and rohs directive compliant agency approvals/compliance 1. compliant with rohs directive applications 1. general purpose detection of paper presence or mo- tion. 2. example: ppc, fax, printer * "opic"(optical ic) is a trademark of the sharp corporation. an opic consists of a light-detecting element and a signal- processing
2 sheet no.: d3-a05101en gp2a200lcs0f series internal connection diagram outline dimensions (unit : mm) product mass : approx. 1.95g voltage regulator amp. comparator oscillator circuit sync. detecting circuit demodulator circuit reflective object 1 2 3 v cc v out gnd 1 2 3 33 17.7 6 6.2 7.8 12 26.5 3 + 0 ? 0.2 3.1 (6.8) 9 4.5 8 4.5 2.5 (7.8) (5.8) (0.65) (0.9) 2 3.2 1 2 3 1 2 3 v cc v out gnd optical center connector : 292133-3 (tyco electronics amp. k. k) 0 7 date code gp2a200lcs0f GP2A200LCSCF gp2a210lcsjf product mass : approx. 1.95g product mass : approx. 2.3g product mass : approx. 1.95g gp2a240lcs0f 02 6 5.2 5.2 10.2 2 3.2 3.5 3.5 4.5 2 7 (5.8) 6.1 9.6 9 12 7.8 (7.8) (6.8) 26.5 32 3 + 0.0 ? 0.2 connector : 292133-3 (tyco electronics amp k.k.) 3 2 1 optical center 3.5 4-sr1 date code 1 2 3 v cc v out gnd view a view a 99 33 (6.8) (7.8) (5 .8) 17.7 6 6.2 3.2 4.5 4.5 2.5 2 9 8 12 7.8 26.5 3.1 3 + 0.0 ? 0.2 connector : 4-292133-3 (yellow) (tyco electronics amp k.k.) 1 2 3 date code 1 2 3 v cc v out gnd optical center 51 33 (6.8) (7.8) (5 .8) (0.65) 17.7 6 6.2 3.2 4.5 4.5 2.5 2 9 8 12 7.8 26.5 3.1 3 + 0.0 ? 0.2 connector : 292133-3 (tyco electronics amp k.k.) 1 2 3 date code 1 2 3 v cc v out gnd optical center connector terminal plating material : sn ? unspeci ed tolerance shall be as follows ; dimensions tolerance less than 6 0.2 6 or more less than 14 0.3 14 or more 0.4 ? *( ) : reference dimensions ? unspeci ed tolerance shall be as follows ; dimensions tolerance less than 6 0.2 6 or more less than 14 0.3 14 or more 0.4 ? *( ) : reference dimensions ? unspeci ed tolerance shall be as follows ; dimensions tolerance less than 6 0.2 6 or more less than 14 0.3 14 or more 0.4 ? *( ) : reference dimensions ? unspeci ed tolerance shall be as follows ; dimensions tolerance less than 6 0.2 6 or more less than 14 0.3 14 or more 0.4 ? *( ) : reference dimensions ? : portion built-in ir-90 lter
3 sheet no.: d3-a05101en gp2a200lcs0f series repeats in a 10 year cycle date code (2 digit) 1st digit 2nd digit year of production month of production a.d. mark month mark 2000 0 1 1 2001 1 2 2 2002 2 3 3 2003 3 4 4 2004 4 5 5 2005 5 6 6 2006 6 7 7 2007 7 8 8 2008 8 9 9 2009 9 10 x 2010 0 11 y : : 12 z country of origin japan
4 sheet no.: d3-a05101en gp2a200lcs0f series absolute maximum ratings electro-optical characteristics (t a = 25 ? c) parameter symbol rating unit supply voltage v cc ? 0.5 to + 7v output voltage v o 30 v *1 output current i ol 50 ma *2 operating temperature t opr ? 10 to + 70 ? c *2 storage temperature t stg ? 20 to + 80 ? c ? 1 sink current refer to fig.5. ? 2 the connector should be plugged in/out at normal temperature. (t a = 25 ? c) parameter symbol condhitions min. typ. max. unit supply voltage v cc ? 4.75 ? 5.25 v current dissipation (i) i cc smoothing value v cc = 5v, r l = ?? 30 ma *3 current dissipation (ii) i ccp pulse peak value v cc = 5v ?? 150 ma low level output voltage v ol v cc = 5v, i ol = 16ma, at detecting time ?? 0.4 v high level output voltage v oh v cc = 5v, r l = 1k , at non detecting time 4.5 ?? v *4 non detection distance l lhl kodak gray cards, v cc = 5v ?? 90 mm gp2a210lcsjf ?? 70 *4 detection distance l hls kodak gray cards, v cc = 5v ?? 2 mm black paper, v cc = 5v ?? 5 l hll kodak gray cards , v cc = 5v 22 ?? mm black paper, v cc = 5v 15 ?? *5 response time t plh v cc = 5v ?? 1ms t phl ?? 1ms *6 acceptable illuminance ev1 ? 3 000 ?? lx ev2 1 500 ?? lx ? 3 refer to fig.1. ? 4 refer to fig.2. ? 5 refer to fig.3. * 6 refer to fig.4. re ective object black paper (black) : standard re ective object (provided by sharp corporation) kodak gray cards (use the white side re ects about 90%) : standard re ective object (provided by sharp corporation) ppc paper : standard re ective object (provided by sharp corporation)
5 sheet no.: d3-a05101en gp2a200lcs0f series fig.2 test condition for detecting distance characteristics v oh v ol l lhs l hls l hll l lhl output v o detecting distance l detection surface reflective object fig.1 test condition for peak pulse value i ccp v o gnd v r t w t p v i ccp = v r /1 t w (typ.) = 8 s ( gp2a240lcs0f : 2.5 to 9.3 s) t p (typ.) = 130 s ( gp2a240lcs0f : 40 to 150 s) v cc = 5v r l = 1k r = 1 1 2 3 photointerrupter fig.3 test circuit for response time v o gnd v oh 1.5v v ol l r l = 1k v out waveform v cc = 5v reflective object detection surface with reflective object without reflective object t phl t plh 1 2 3 photointerrupter e v1 : at non-detecting e v2 : at detecting illuminance shall be that on the emission/detection surface. output shall not go from "h" to "l". illuminance shall be that on the reflective object. output shall not go from "l" to "h". light source a emission/detection surface ppc paper 15mm emission/detection surface light source a photointerrupter photointerrupter fig.4 test condition for external disturbing light illuminance
6 sheet no.: d3-a05101en gp2a200lcs0f series fig.5 output current vs. ambient temperature fig.6 low level output voltage vs. ambient temperature fig.7 low level output voltage vs. low level output current fig.8 dissipation current(smoothing value) vs. ambient temperature 0 10 20 30 40 50 ? 100 255075 70 100 ambient temperature t a (c) output current i ol (ma) v cc = 5v at detecting low level output voltage v ol (v) ambient temperature t a (c) 0 0.3 0.2 0.1 ? 100 10203040506070 i ol = 30ma 16ma 5ma low level output current i ol (ma) low level output voltage v ol (v) 1 10 100 0.01 0.1 v cc = 5v at detecting dissipation current i cc (ma) 0 7 6 5 4 3 2 1 4.75 4.85 4.95 5.05 5.15 5.25 supply voltage v cc (v) t a = ? 10 ? c 25 ? c 70 ? c remarks : please be aware that all data in the graph are just for reference and not for guarantee.
7 sheet no.: d3-a05101en gp2a200lcs0f series design considerations design guide 1) v o terminal : open collector output this product operates the light emitter by pulse drive. please supply the stable supply voltage in order to prevent error operation by pulse current. please use this device after connecting a capacitor between v o and gnd for prevention of line noise. 2) prevention of detection error please be careful that you need to keep the direct inverter light away from the photo detecting surface since the device will not operate correctly in such case. in addition, we recommend to make sure the operation test in the actual application. 3) plugging in/out the connector should be plugged in/out at normal temperature. this product is not designed against irradiation and incorporates non-coherent ired. parts this product is assembled using the below parts. ? photodetector (q'ty : 1) [using a silicon photodiode as light detecting portion, and a bipolar ic as signal processing circuit] category maximum sensitivity wavelength (nm) sensitivity wavelength (nm) response time ( s) phototransistor 900 700 to 1 200 400 ? photo emitter (q'ty : 1) category material maximum light emitting wavelength (nm) i/o frequency (mhz) infrared emitting diode (non-coherent) gallium arsenide (gaas) 950 0.3 ? material case lens bottom cover gp2a200lcs0f black polyphernylene sul de resin (ul94 v-0) polycarbonate resin (ul94 v-2) polycarbonate resin (gray) (ul94 v-2) GP2A200LCSCF gp2a210lcsjf ? gp2a240lcs0f polycarbonate resin (navy blue) (ul94 v-2) ? the ir-90 lter (fuji photo film co., ltd.) is inserted between case and detector side lens. ? others laser generator is not used.
8 sheet no.: d3-a05101en gp2a200lcs0f series manufacturing guidelines cleaning instructions polycarbonate resin is used as the material of the lens surface. so this product shall not be cleaned by cleaning solvent absolutely. dust and stain shall clean by air blow, or shall clean by soft cloth. presence of odc this product shall not contain the following materials. and they are not used in the production process for this product. regulation substances : cfcs, halon, carbon tetrachloride, 1.1.1-trichloroethane (methylchloroform) speci c brominated ame retardants such as the pbbos and pbbs are not used in this product at all. this product shall not contain the following materials banned in the rohs directive (2002/95/ec). ?lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (pbb), polybrominated diphenyl ethers (pbde).
9 sheet no.: d3-a05101en gp2a200lcs0f series package speci cation case package package materials anti-static plastic bag : polyethtylene moltopren : urethane packing case : corrugated berboard package method 100 pcs of products shall be packaged in a plastic bag, ends shall be sealed by stapler. the bottom ot the packing case is covered with moltopren, and 2 plastic bags shall be put int the packing case. moltopren should be located after all product are settled (1 packing conteains 200 pcs). packing composition moltopren plastic bag packing case
10 sheet no.: d3-a05101en gp2a200lcs0f series important notices the circuit application examples in this publication are provided to explain representative applications of sharp devices and are not intended to guarantee any circuit design or license any intellectual property rights. sharp takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of sharp's devices. contact sharp in order to obtain the latest device specification sheets before using any sharp device. sharp reserves the right to make changes in the speci cations, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. manufacturing locations are also subject to change without notice. observe the following points when using any devices in this publication. sharp takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used speci ed in the relevant speci cation sheet nor meet the following conditions: (i) the devices in this publication are designed for use in general electronic equipment designs such as: --- personal computers --- of ce automation equipment --- telecommunication equipment [terminal] --- test and measurement equipment --- industrial control --- audio visual equipment --- consumer electronics (ii) measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when sharp devices are used for or in connection with equipment that requires higher reliability such as: --- transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- traf c signals --- gas leakage sensor breakers --- alarm equipment --- various safety devices, etc. (iii) sharp devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- space applications --- telecommunication equipment [trunk lines] --- nuclear power control equipment --- medical and other life support equipment (e.g., scuba). if the sharp devices listed in this publication fall within the scope of strategic products described in the foreign exchange and foreign trade law of japan, it is necessary to obtain approval to export such sharp devices. this publication is the proprietary product of sharp and is copyrighted, with all rights reserved. under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of sharp. express written permission is also required before any use of this publication may be made by a third party. contact and consult with a sharp representative if there are any questions about the contents of this publication. [h176]
|
